Our Click flooring can be applied in wet areas, it must be dried immediately when exposed to water. There should not be excessive and permanent water on the surface. Note: Only the flooring material is 100% waterproof. Moisture and floods can still affect the lower layer/substrate, which can cause product deterioration. However, the flooring material can be removed. It can be dried and re-installed.
The warranty period for LVT products is 5 years for commercial and 10 years for housing. In this case, please take the Warranty Terms into consideration. Only the LVT floor product is included in the warranty.
Our LVT flooring products; 2.5 mm Dry-Back product is applied with glue. 5mm click is installed with click-through click system, floating system. 5mm click product is for large areas; It is recommended not to be used in areas exceeding 80m2 and exposed to sunlight and/or wet areas. Instead, the 2.5mm Dry Back product is recommended. 5 mm Click products can be used in areas other than these.
Avoid prolonged exposure of the flooring to direct sunlight. Minimize the impact of sunlight directly on the floor covering using a curtain or sun visor during times of strong sunlight. Most types of floor coverings tend to discolor when exposed to direct sunlight. In addition, high temperatures affect the quality of LVTs.
Refer to the Maintenance and Repair Guide for adhesives that should be used in Dry-Back LVT applications. If the application is done according to the required standards, an average of 350 g / m2 glue is applied.
LVT floor covering is fire resistant. The BFL-S1 class is the best possible class for floor coverings. It can be applied in schools, hospitals, kindergartens, commercial enterprises, and many other areas. Our floors have successfully passed all tests and have remained well within the legal tolerance of all values. Thus, it complies with strict European standards for fire safety.
LVT flooring is completely harmless to human health. It does not contain dangerous phthalate acid and plasticizers. It does not contain dust, mite, and other micro-organisms. With this feature, it provides a unique hygiene. In addition, LVT flooring is subject to strict EU regulations and is under supervision. In this way, you can use it in all places that require hygiene.
LVT flooring can be safely used with underfloor heating systems. The LVT quickly heats up and cools down quickly. The floor heating system must not exceed 27 ° C when floor covering with the underfloor heating system is performed. This is achieved by a programmed thermostat to connect the system with LVT floors. For detailed information, please refer to the Application and Maintenance Instruction.
The top surface of LVT products is equipped with a durable polyurethane top coat. This protective equipment not only undertakes a protective task during transport but also protects against damage, contamination or staining during and after installation. Recommended surface cleaning materials are required. (Take the cleaning agent recommendations into consideration. -Dr. Schutz-). Never use abrasives for cleaning and maintenance. (Scouring powder, soft soap, bleach, acetone, alcohol, porous, polish wax, dissolvents etc. ..). The floor should be wiped with a damp mop at least once a week in order to maintain its beautiful appearance.
Yes, it can be replaced with a new product. It is strongly recommended that this change be carried out by an experienced master. You can contact the manufacturer Technical Service for detailed information.
All of our LVT collections are 100% waterproof. Therefore, the plates and tiles will not rise or lose their integrity when exposed to water. This makes them perfect, including kitchens, bathrooms, various rooms, and basements. Note: Only the flooring material is 100% waterproof. Moisture and floods can still affect the lower layer/substrate, which can cause product deterioration. However, the flooring material can be removed. It can be dried and re-installed.
Yes, you can use a carpet as long as it is labeled by the manufacturer as “fast”. We recommend non-painted, vinyl-supported mats and woven rugs. We do not recommend the use of rubber or latex-supported mats. Because the back face can be permanently stained by the chemical (antioxidant) floor used to prevent it from being brittle.
You don’t need a blanket for dry-back LVT floorings. All you have to do is make sure that the bonding process is done according to the installation instructions. If the floor conditions for the floating (click) system of LVT floors are smooth, dry, clean, free of cracks, and non-porous, then the blanket can be applied. LVT floor products are much more elastic than laminate or parquet flooring. In order to avoid permanent marks on the floor, we recommend that you always use a blanket that will withstand the pressure of the floor.
LVT products are not suitable for outdoor areas, outdoors and winter gardens. Note about the winter gardens in particular: Very high and directly exposed to 50 ° C temperature. (For example, fully glazed winter gardens …). We do not recommend the usage of it. It is important to note that the LVT flooring is applied and held at a constant temperature in the range of 18-27 ° C before and after the installation.
LVT flooring does not require any polishing and maintenance like wood flooring or laminate. Unlike other indoor floor coverings, LVT is not affected by water, its special structure is also antibacterial. Since it is a multi-layer material, the sound insulation is higher than other products. Surface corrosion is at the lowest level. It can bear heavy foot traffic without any problems. LVT flooring is fire resistant. We also have a suitable design in all kinds of housing and all commercial applications with different colors, patterns, textures and a wide variety of styles and preference options. Due to its flexible structure, the LVT provides comfort while standing and working on it.
If the floor to be laid with LVT is a long area, a dilatation profile should be placed at 15 m intervals. The space between the materials with the dilatation profile should be at least 7 mm. The assembly details of all the Click products should be checked with the help of a miter and a ruler before installation, and no product that might cause a miter or assembly problem should be installed.